The requirements, confirmation, design, production and installation of the pedestrian passage gates are very critical. Beijing Simolo has paid attention to every detail as a manufacturer. Today, it is only possible to swing the wiring to go into detailed instructions. It is very helpful for the manufacturer and integrators installed by the manufacturer. After all, the personnel who often do the gate project can understand that the actual wiring error will cause the intelligent swing gate to be unstable or unable to operate. Will cause damage to the gate.

Intelligent swing gate wiring manual

1. Generally, the expansion bolt can be fixed on the swinging base of the pedestrian swing. If a simple set of intelligent swing gates is installed, it is necessary to connect a power cord to the internal controller of the swing gate, and then fix the swing gate, and normally swipe the card. The pass test is OK. But the specific operation still has to pay attention to many problems.

Second, wiring: According to the design drawings on-site measurement, to the swing gate positioning;

After the installation swing position is fixed, draw the mark in advance, start to dig the line to bury the power line pipe, thread the line into the tube, and connect the swing gate system protection ground wire.

Third, UPS assembly

Fourth, the intelligent swing gate fixed: then the pedestrian gate is fixed, the gates of the left and right swing gates of each channel should be aligned, and test whether it is on a horizontal line.

V. Installation, power-on commissioning test equipment access, after completion, the dug line is sealed with cement!

Intelligent swing gate wiring manual, explain in detail the paper description in the Ximo Luo gate delivery list and the gate chassis, for other problems that do not understand the swing gate gate three roller gates, etc., you can pay attention to the face at any time. Identify the brake manufacturer Beijing Simolo.

High Frequency Welding Tube Mill

Our High Frequency Welding Tube Mill is intended for manufacturing of round pipe of Î¦16mm-Î¦127mm with thickness of 0.5 mmâ€“5.0 mm from cold-rolled and hot-rolled coil strip by means of unclosed tubular blank with its subsequent welding into tube, edge heating by means of solid state high-frequency welder, longitudinal seam welding in rolls of tube welding machine, cooling, further sizing or shaping and on-stream cutting of endless tube in measured lengths.

Finished product can be of round, square or rectangular pipes.

a) High Frequency Welding Tube Mill Specifications:
Pipe diameter: Ã˜16â€“Ã˜127mm
Pipe Thickness: 0.5â€“ 5.0mm
Pipe Length: 6-9m

Length Tolerance: 0-3mm

b) High Frequency Welding Tube Mill Steel Tape Specifications:
Material: Low Carbon steel (Î´bâ‰¤500Mpa, Î´sâ‰¤235Mpa)
Inner diameter: Î¦580-Î¦610mm
Outer diameter: Î¦900-1500mm
Strip steel thickness: 0.5mm-5.0mm

The maximum weight: 5.0 tons

c) High Frequency Welding Tube Mill Electricity:
Dynamic power: AC380VÂ±10%, 3phases, 50HzÂ±10%
Control Power: AC220VÂ±10%, one phase, 50Hz Â±10%

Electric installed capacity: appro 450KW

e) High Frequency Welding Tube Mill Cooling water:
Reservoir for High Frequency equipment:15 mÂ³, one set
Reservoir for circulating cooling water:15 mÂ³, one set
f) High Frequency Welding Tube Mill Compressed air:
Pressure: 0.4Mpa
Flow: 0.5m3/h

g) High Frequency Welding Tube Mill speed:

30-90m/min

Why choose to cooperate with us ?
1. We are professional manufacturer, so we can offer better price and after-sale service and shorter delivery time.
2. We have strong design & technical ability, we can design and manufacture as customer's requirement.
3. Our factory has been approved ISO 9001 certificate.
4. We have much experience for installation and training experience overseas.
5. We have successfully exported our machines to more than 90 countries, We all get good feedback.
6. We provide a free two years warranty for all our items.

7. OEM brand.

High Frequency Welding Tube Mill FAQ:
1.How to get a quotation of tube rolling line ?
Give me the diameters and thickness for the pipe .
Other spicific requirements is welcome, such as the speed,power and voltage you want.
2. Terms of payment ?

30% T/T, Balance to be paid before shipping after inspection.Also we accept the payment L/C, O/A , D/P.

3. What is your after-sale service ?

High Frequency Welding Tube Mill warranty period is 24 months, if the broken parts can't be repaired, we can send new to replace for free, but you need to pay the express cost yourself. we supply the technical support for the whole life of the equipment.

4. How to visit your factory ?
a.Fly to Beijing airport: By high speed train From Beijing Nan to Cangzhou Xi (1 hour), then we can pick up you.
b.Fly to Shanghai Airport: By high speed train From Shanghai Hongqiao to Cangzhou Xi(4.5 hours), then we can pick up you.

Steel Pipe Roll Forming Machine

Steel Pipe Roll Forming Machine,Carbon Steel Pipe Making Machine, High Frequency Welding Pipe Making Machine,Steel Pipe Making Machine

Zhongtuo Roll Forming Machinery Co., ltd , https://www.rollsformingmachines.com